Elitegroup MD100/MD110 (V1.0) Manual Manuel d'utilisateur

3Introducing the 3L Small Form FactorOnboard LANThe onboard LAN controller provides either of the following features:• Integrated 10BASE-T/100BASE-TX

4Introducing the 3L Small Form FactorMotherboard Components

5Introducing the 3L Small Form FactorTable of Motherboard ComponentsThis concludes Chapter 1. The next chapter explains how to install the motherboard

6Introducing the 3L Small Form FactorMemo

7Installing the MotherboardChapter 2Installing the MotherboardSafety Precautions• Follow these safety precautions when installing the motherboard• Wea

8Installing the MotherboardChecking Jumper SettingsThis section explains how to set jumpers for correct configuration of the motherboard.Setting Jumpe

9Installing the MotherboardChecking Jumper SettingsThe following illustration shows the location of the motherboard jumpers. Pin 1 islabeled.Jumper Se

10Installing the MotherboardDDR2 SDRAM memory module tableInstalling Memory ModulesThis motherboard accommodates one or two memory modules. It can sup

11Installing the MotherboardInstallation ProcedureThese modules can be installed with up to 2GB system memory. Refer to the followingto install the m

12Installing the MotherboardTable A: DDR2 (memory module) QVL (Qualified Vendor List)The following DDR2 800/667/533 memory modules have been tested an

13Installing the MotherboardInstalling Add-on CardsThe slots on this motherboard are designed to hold expansion cards and connectthem to the system bu

14Installing the MotherboardConnecting Optional DevicesRefer to the following for information on connecting the motherboard’s optionaldevices:JUSB1~2:

15Installing the MotherboardInstalling SATA_HDDAbout SATA_HDD1 ConnectorThis motherboard features one SATA HDD1 connector supporting one drive, andyou

16Installing the MotherboardConnecting I/O DevicesThe backplane of the motherboard has the following I/O ports:LAN PortConnect an RJ-45 jack to the LA

17Installing the MotherboardConnecting Case ComponentsAfter you have installed the motherboard into a case, you can begin connecting themotherboard co

18Installing the MotherboardLED1~4LED1 (System Power LED)The system power LED can be used to indicate system power status. The LED is onwhen the syste

19Using BIOSChapter 3Using BIOSAbout the Setup UtilityThe computer uses the latest “American Megatrends Inc. ” BIOS with support forWindows Plug and P

20Using BIOSBIOS Navigation KeysThe BIOS navigation keys are listed below:CMOS Setup Utility -- Copyright (C) 1985-2005, American Megatrends, Inc. v02

21Using BIOSUpdating the BIOSYou can download and install updated BIOS for this motherboard from themanufacturer’s Web site. New BIOS provides support

22Using BIOSStandard CMOS SetupThis option displays basic information about your system.Date Mon 01/01/2007SATA 1 Not DetectedSATA 2 Not DetectedHelp

23Using BIOSLBA/Large ModeUse this item to set the LAB/Large mode to enhance hard disk performance byoptimizing the area the hard disk is visited each

24Using BIOSAdvanced SetupThis page sets up more advanced information about your system. Handle this pagewith caution. Any changes can affect the oper

25Using BIOSBoot Other DeviceWhen enabled, the system searches all other possible locations for an operatingsystem if it fails to find one in the devi

26Using BIOSDVMT/FIXED MemoryWhen set to Fixed Mode, the graphics driver will reserve a fixed portion of thesystem memory as graphics memory. When set

27Using BIOSPower Management SetupThis page sets up some parameters for system power management operation.Select the ACPIstate used forSystem Suspend.

28Using BIOSResume on RTC AlarmThe system can be turned off with a software command. If you enable this item, thesystem can automatically resume at a

29Using BIOSSMART FAN ControlThis item allow you to enable or disable the control of the system fan speed bychanging the fan voltage.SMART FAN start P

30Using BIOSFrequency/Voltage ControlThis page enables you to set the clock speed and system bus for your system. Theclock speed and system bus are de

31Using BIOSSupervisor PasswordThis item indicates whether a supervisor password has been set. If the password hasbeen installed, Installed displays.

32Using BIOSUser PasswordThis page helps you install or change a password.Help ItemCMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends

PrefacePrefaceCopyrightThis publication, including all photographs, illustrations and software, is protectedunder international copyright laws, with a

33Using the Motherboard SoftwareChapter 4Using the Motherboard SoftwareAuto-installing under Windows VistaThe support software CD-ROM disc loads autom

34Using the Motherboard SoftwareSetup TabSetupClick the Setup button to run the software installation program.Select from the menu which software you

35Using the Motherboard Software2. Click Next. The following screen appears:3. Check the box next to the items you want to install. The default option

36Using the Motherboard SoftwareMethod 1. Run Reboot SetupWindows Vista will block startup programs by default when installing drivers after thesystem

37Using the Motherboard Software2. Select Classic View.3. Set User Account.4. Select Turn User Account Control on or off and press Continue.

38Using the Motherboard SoftwareManual InstallationInsert the CD in the CD-ROM drive and locate the PATH.DOC file in the rootdirectory. This file cont

iiPrefaceDeclaration of ConformityThis device complies with part 15 of the FCC rules. Operation is subject to thefollowing conditions:• This device ma

iiiTTTTTABLE OF CONTENTSABLE OF CONTENTSABLE OF CONTENTSABLE OF CONTENTSABLE OF CONTENTSPreface iChapter 1 1Introducting the

ivIntegrated Peripherals...26Power Management Setup...

1Introducing the 3L Small Form FactorChapter 1Introducing the 3L Small Form FactorIntroducting the 3L Small Form FactorThank you for choosing 3L Small

2Introducing the 3L Small Form FactorFeature of the motherboard• Onboard Intel® AtomTM single core, 1.60GHz CPU speed with 512KBcache• Supports a syst